Коллиматорный прицел Leupold DeltaPoint Pro Reflex Sight, 2.5 MOA Dot, 119688

Features• DiamondCoat™, scratch resistant aspheric lens for brightness, andresolution• Motion Sensor Technology (MST™)• Extremely durable, ultra light aluminum housing• Small size and lightweight• Unlimited eye relief• For handguns, rifles and shotguns• Wide field-of-view• Blackened lens edges• Waterproof to 33ft.Specifications• Magnification: 1.0x• Sight window: 25.7mm x 17.5mm; 1.01” x 0.68”• Elevation adjustment range: 60 MOA• Windage adjustment range: 60 MOA• 40 MOA per revolution of adjustment (1 MOA per click)• Subtension of the aiming point : 2.5 MOA Dot, 7.5 MOA inscribed Delta• Operating Temperature Range: -20°F to +120°F (-29°C to +49°C)• Storage Temperature Range: -40˚F to +160˚F (-40˚C to +71˚C)• Power Supply: 3V with one CR 2032 Lithium battery• Dimensions: (LxWxH) 1.82” x 1.31” x 1.30” (46.1mm x 33.2mm x 33.0mm)• Weight (with battery installed): 1.9oz. (53.8g)

Package Contents• DeltaPoint Pro Reflex Sight, Delta (SKU 119687) or• DeltaPoint Pro Reflex Sight, 2.5 MOA Dot (SKU 119688)• (1) 3V Lithium battery (CR 2032)• (1) Protective cover• (2) M4x.7x15.8mm Torx® head screws for installing the sight on themounting plate• (1) Torx® T-15 wrench• (1) 1/16 Hex wrench• Operating InstructionsAccessories (sold separately)• Cross-Slot Mount (SKU 120056)• Rear Iron Sight (SKU 120058)• Cross-Slot Riser (SKU 120059)• All Pistol Mounts Kit (SKU 120057)

Battery InstallationThe unit operates with one commerciallyavailable 3V Lithium battery (CR 2032) only.Open the battery cover by pulling back thebattery door release latch. Insert the batteryso the positive side (+) is facing up andclose the battery cover. Push the batterydoor release latch into place. Verify the whitewitness mark is fully covered by the latch.Keep the contact surface clean of dirt andcorrosion, cleaning with alcohol if necessary.Illumination OperationDeltaPoint Pro is equipped with eight illumination intensities. To activatethe DeltaPoint Pro press and release the power button. Cycling throughthe illumination intensities is done by repeatedly pressing and releasingthe power button. When the highest or lowest setting is reached, the LEDwill flash 5 times. To change the direction of adjustment, i.e., change fromincreasing intensity to decreasing intensity, press and hold the power buttonfor 2 seconds and immediately release the button. Then continue pressingand releasing to change intensity.To power the DeltaPoint Pro off, press and hold the power button forapproximately 3 seconds, or until the LED turns off. When reactivated, theunit will return to the last known setting.Low Battery IndicatorThe DeltaPoint Pro has a unique feature that flashes the aiming point 10times when low battery power is detected. The operator will have severalhours of operating time in this mode before the sight is rendered inoperablewithout a battery change.Power-Saving Mode (Motion Sensor Technology™)After the optic has been completely at rest for 5 minutes the sight transfersto sleep mode, thus nearly eliminating all battery drain. Upon any movementof the optic, the system powers up the LED to the last known setting. Theunit will flash 10 times before automatic power off. The motion sensor willNOT reactivate the DeltaPoint Pro if it has been turned off manually.

InstallationNote: If you are installing the DeltaPoint Pro on a milled slide, the mountbase & dovetail are not required.Installation on most handguns requires the use of one of the optional mountbases (sold separately) . Leupold recommends utilizing a qualified gunsmithto press/remove the rear sight from your handgun. Once the rear sight hasbeen removed, the appropriate dovetail replaces the rear sight, with thepart number facing up. Some installations (Kimber / Smith & Wesson M&P)require the use of the set screws to be placed in the dovetail to hold it inplace and the M4x.7x15.8mm Torx® screws will fasten into the dovetail plateextension.The corresponding mount base for your pistol is placed on top of the slideand over the dovetail with the flat part number side facing up through theslot in the base. Once the dovetail and mount base have been placed onthe slide, the DeltaPoint Pro is placed on top of the base. The four holesin the bottom of the DeltaPoint Pro will align with the four short postson the mount base and secure into the dovetail using the two includedM4x.7x15.8mm Torx® screws ( Figure 1). Secure the screws by applying 25inch pounds of torque. Securing these screws creates a press-fit and willhold the DeltaPoint Pro firmly in place. Call Leupold customer service fordetails specific to your handgun. For rifle/shotgun applications, the CrossSlotMount allows fast and easy mounting on Weaver-style or Picatinnybases/rails. Smith & Wesson® Revolver Mount(For use with Smith & Wesson Classic pre-drilled and tapped K, L, N & X framerevolvers, including .500)Remove the rear sight and retain the sight and all mounting hardware forfuture use if necessary. Place the insert (10A) into the mount base (10B)and set both pieces on the revolver as shown above. Install the two 6-48x.210 screws through the dovetail insert and into the last two tapped holes,nearest the hammer in the frame of the revolver (Figure 2). Tighten to 20inch pounds.10B Mount Base10A Insert6-48x .210 Screws(Figure 2)M4x 14mm Screws(Figure 3)Place the DeltaPoint Pro on the mount base so that the four holes in thebottom of the DeltaPoint Pro will align with the four short posts on themount base and the screw holes in the sight and mount base align (Figure3), then secure the sight with the two M4 x 14mm screws using 20 inchpounds of torque.

Operating ProcedureElevation and Windage AdjustmentSeparate controls for the elevation and windage adjustments are found onthe top and right side of the sight. Turn the UP or “R” (RIGHT) screws with ascrewdriver, cartridge rim or coin. The windage adjustment mechanism haslimit stops at both ends.Zeroing the Point-of-ImpactThe DeltaPoint Pro windage and elevation screws move the point of impact40 MOA (10” @ 25 yds) per revolution of the dial (1 MOA per click).Boresighting the DeltaPoint Pro Reflex Sight To make the boresighting process easier, Leupold recommends placing the eyenear the DeltaPoint Pro while making windage/elevation adjustments. As withany boresighting procedure, be sure to follow all safety precautions prior toboresighting, and make sure the boresighter has been removed from the barrelprior to loading the magazine or chamber.Leupold Gold Ring™ Full Lifetime GuaranteeIf any Leupold Gold Ring product is found to have defects in materials or workmanship, Leupold &Stevens, Inc. will repair, or if repair is not possible, either replace the product or refund the purchaseprice, whichever you prefer. FREE. Even if you are not the original owner. No warranty card isrequired. No time limit applies. This warranty excludes electronic components, which are subject tothe limited two-year warranty below.Leupold Gold Ring Electronics LimitedTwo-Year WarrantyThis warranty covers any defects in materials and workmanship in the electronic componentsof illuminated riflescopes/sights, flashlights, flashlight components, RX Rangefinders, GXRangefinders, Pin Caddie Rangefinder, RCX Cameras and Vendetta Archery Rangefinder. Thiswarranty lasts for two years from the date of purchase. If, during that two-year period, theseproducts are found to have defects in materials or workmanship, Leupold will repair, or if repair isnot possible, replace the product, free of charge.Warranty ExclusionsUnfortunately, these warranties do not apply if the product has been modified, misused or hasbeen damaged by accident, abuse, or misapplication. To ensure this doesn’t happen to you, contactLeupold Product Service before having any work or repairs done to your valuable Leupold optics.Call 1-800-LEUPOLD or (503) 526-1400. If your Leupold product fails to perform in any way, pleasecontact a Leupold Product Specialist within our Product Service department to determine if theproblem can be solved without sending the product to Leupold. Many times, the problem can besolved without sending the product to us. Leupold Technical Service will assist you with the problemin the best and most efficient manner.To Reach Leupold Product ServicePhone:7:00 a.m. - 4:30 p.m. PST M-F 1-800-LEUPOLDor (503) 526-1400Fax:24 hours a day, 7 days a week(503) 352-7621E-mail:productspecialist@leupold.comParcel ServiceLeupold Product Service14400 NW Greenbrier ParkwayBeaverton, OR 97006-5791 USAPostal ServiceLeupold Product ServiceP.O. Box 688Beaverton, OR 97075-0688 USALEUPOLD, GOLDEN RING, MARK 4, the Golden Ring design, the circle-L reticle logo design, andvarious other marks are registered trademarks of Leupold & Stevens, Inc. All marks, includingcorporate logos and emblems, are subject to Leupold’s rights and may not be used in connectionwith any product or service that is not Leupold’s, or in any manner that disparages or discreditsLeupold, or in a manner likely to cause confusion.Certain other trademarks used in connection with Leupold products and services are the propertyof their respective owners, and are used with permission. BOONE AND CROCKETT CLUB and BOONEAND CROCKETT are registered trademarks of the Boone and Crockett Club. RMEF and ROCKYMOUNTAIN ELK FOUNDATION are registered trademarks of the Rocky Mountain Elk Foundation.ADVANTAGE TIMBER and ADVANTAGE TIMBER HD are trademarks or registered trademarks of JordanOutdoor Enterprises Ltd. MOSSY OAK BREAK-UP, MOSSY OAK BRUSH, MOSSY OAK OBSESSION, andMOSSY OAK TREESTAND are trademarks or registered trademarks of HAAS Outdoors, Inc. A.R.M.S. isa registered trademark of Atlantic Research Marketing Systems, Inc.We reserve the right to make design and/or material modifications without prior notice.Copyright © 2015 Leupold+Stevens, Inc. All rights reserved.Caution: Boresighting the DeltaPoint ProVerify that the magazine of the firearm has been removed or emptied, and that thereis not a round in the chamber. Only after double checking the firearm, verifying it isempty and safe, should you proceed with the boresighting process. Be sure to removethe boresighter from the the barrel prior to loading the magazine or chamber.